Promag CON-485 Series Instruções de Operação Página 38
- Página / 98
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
5 Operation / adjusting device settings - Set-up to commissioning Memo-Graph S
38 Endress+Hauser
Only when using the digital input as impulse counter
Continued: effect of the control
input
“Reset batch number”: if “Autom. incrementation (6 characters)” has been selected under “Basic settings - Operating
modes - Batch operating mode”, a new batch number is generated with each new batch start, in which this number is
incremented by 1. With this digital input, this 6-digit batch number can be set back to zero externally.
! Note!
The input must be activated for min.1 second, in order to carry out this function.
“green operating LED”: only available if “controlled with two DI” has been selected as the LED operating mode under
operating modes.
The front-mounted green operating LED lights up when the digital input is active.
“red fault LED”: only available if “controlled with two DI” has been selected as the LED operating mode under operating
modes.
The front-mounted red fault LED lights up when the digital input is active.
“H->green, L->red LED”: only available if “controlled with one DI” has been selected as the LED operating mode under
operating modes.
The front-mounted green operating LED lights up when the digital input is active (high).
The front-mounted red fault LED lights up when the digital input is inactive (low).
“L->green, H->red LED”: only available if “controlled with one DI” has been selected as the LED operating mode under
operating modes.
The front-mounted green operating LED lights up when the digital input is inactive (low).
The front-mounted red fault LED lights up when the digital input is active (high).
Set-up -> Signal settings -> Digital inputs -> Digital input x
Set-up -> Signal settings -> Digital inputs -> Digital input x
Function Impulse counter
Designation Description of the function or measuring point name carried out with this input.
Engineering units Technical unit of the counting input. e. g. liter, m3, ... .
Decimal point Number of places after decimal point for the display.
1 impulse = Impulse factor = factor which provides the physical value when multiplied by an input impulse.
Example:
1 impulse corresponds to 5 m3 -> Enter “5” here.
Total/year counter Initial setting for the total/year counter. Useful, for example, for continuing a measurement previously equipped with
(electro) mechanical counter.
" Caution!
The setting to this value takes effect when you leave the device set-up.
- Safety Data Manager (SDM) 1
- Memo-Graph S 1
- Overview 2
- Brief overview 2
- CHANGE PROTOCOL 3
- Table of contents 5
- 1 Safety instructions 7
- 1.4 Operational safety 8
- 1.5 Return 8
- 2 Identification 9
- 2.1.2 Product structure 10
- 3 Installation 11
- 3.3 Installation instructions 12
- 3.4 Post-installation check 12
- 4 Wiring 13
- 4 Wiring Memo-Graph S 14
- 14 Endress+Hauser 14
- 4.2 Terminal diagram 15
- 4.2.5 CPU board (slot 0) 19
- Ethernet connection 21
- 4.4 Ingress protection class 22
- 4.5 Post-connection check 22
- Set-up to commissioning 23
- 5.5 Set-up using PC 26
- 5.7.1 Basic settings 27
- 5.7.2 Signal settings 31
- Factory setting “0” 32
- 36 Endress+Hauser 36
- # Warning! 37
- " Caution! 38
- Endress+Hauser 43 43
- 44 Endress+Hauser 44
- 5.7.4 Products 48
- 5.7.5 Texts 50
- 5.7.6 Administration 50
- 5.7.8 Service 53
- 5.9.1 RS 232 56
- 5.9.2 RS 485 56
- 5.9.3 PROFIBUS DP 56
- 5.10.2 MAC address 58
- 5.10.3 IP address allocation 58
- 5.10.4 Subnet mask allocation 59
- 5.10.5 Gateway allocation 59
- 21 CFR 11 61
- 6.2.3 Administration 63
- 6.2.5 Analogue inputs 64
- 6.3.1 General 64
- Endress+Hauser 67 67
- 68 Endress+Hauser 68
- 7 Procedure in operation 69
- 7.2 The functions in detail 72
- 7.2.3 Enter comment / text 74
- 7.2.5 Extras 74
- 7.2.6 Set-up 77
- 8Accessories 78
- Software 79
- Operating language 79
- RSG12A1 79
- 80 Endress+Hauser 80
- 9.4 Spare parts 81
- 9.4.2 Spare parts list 82
- Endress+Hauser 83 83
- 9.5 Repairs/return 84
- 9.6 Disposal 84
- Measured variable / 85
- _ _ _ _ _ 86
- 10.3 Output values 87
- 10.4 Power supply 87
- 10.5 Accuracy 88
- 10.6 Operating conditions 88
- 10.7 Mechanical construction 89
- 320 mm (12.6“) 91
- 320 mm (12.6 “) 91
- 254 mm (10 “) 91
- 10.9 Data storage 92
- 10.11 Accessories 93
- 10.12 Further documentation 93
- BA 138R/09/en/08.04 98
- 51006049 98
- FM+SGML 6.0 98
Manuais e produtos relacionados com Ferramentas de medição e layout Promag CON-485 Series
(40 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais