Promag CON-485 Series Instruções de Operação Página 72
- Página / 98
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
7 Procedure in operation Memo-Graph S
72 Endress+Hauser
Saving device settings / saving onto ATA flash card:
Extras - ATAFlash - Save set-up to ATAFlash
Reading in device settings / loading ATA flash card:
Extras - ATAFlash - Load set-up from ATAFlash
Saving IDs / saving to ATA flash card:
Extras - ATAFlash - Save IDs to ATAFlash
Reading in IDs / loading from ATA flash card:
Extras - ATAFlash - Load IDs from ATAFlash
Checking memory capacity:
Extras - Hardware
Checking ATA flash card technical data:
Extras - Hardware - ATAFlash
Checking device hardware and software status:
Extras - Hardware - Hardware
Switching zoom display on/off in horizontal curve display:
Extras - Switch zoom display on/off
Relay/OC: Simulating power failure / Restoring normal operation
“Set-up” key
Displaying device settings:
Set-up - Select chapter and corresponding operating position(s) / parameters
7.2 The functions in detail
7.2.1 Logging in/out (“Login” key)
In order to be sure who was responsible for the device / process at which time, the operator has to
log in with a unique ID/password combination (“Electronic signature”).
Typically, the administrator provides an initialisation password. The user has to enter it the first time
he logs in and then replace it with a password that only he knows. The operator can not work on
the device until logging in (“Login”) with a unique ID/password combination that only he knows.
!
Note!
• Ensure that the password, and thereby the unique ID/password combination, is only known by
the respective user, in order to prevent misuse of the electronic signature.
• All users who work on the device must be aware that the “Electronic signature” is legally equally
as binding as a hand-written signature on a conventional document.
• Depending on the settings, the device checks the first x characters of the password.
• Depending on the settings, it is possible that the user may have to renew his password every x
days.
• The ID (and possibly an initialisation password) is allocated to you by the administrator and must
be unique (there must not be any duplicate IDs).
• Login/logout functions are saved automatically in the Audit Trail.
• However, only one user can have responsibility at one time. Responsibility can either be handed
over by the old user logging out and then the new user logging in. Alternatively, the new user can
assume responsibility by logging in (is displayed in the Audit Trail by simultaneous logging in and
out by the old and the new user).
- Safety Data Manager (SDM) 1
- Memo-Graph S 1
- Overview 2
- Brief overview 2
- CHANGE PROTOCOL 3
- Table of contents 5
- 1 Safety instructions 7
- 1.4 Operational safety 8
- 1.5 Return 8
- 2 Identification 9
- 2.1.2 Product structure 10
- 3 Installation 11
- 3.3 Installation instructions 12
- 3.4 Post-installation check 12
- 4 Wiring 13
- 4 Wiring Memo-Graph S 14
- 14 Endress+Hauser 14
- 4.2 Terminal diagram 15
- 4.2.5 CPU board (slot 0) 19
- Ethernet connection 21
- 4.4 Ingress protection class 22
- 4.5 Post-connection check 22
- Set-up to commissioning 23
- 5.5 Set-up using PC 26
- 5.7.1 Basic settings 27
- 5.7.2 Signal settings 31
- Factory setting “0” 32
- 36 Endress+Hauser 36
- # Warning! 37
- " Caution! 38
- Endress+Hauser 43 43
- 44 Endress+Hauser 44
- 5.7.4 Products 48
- 5.7.5 Texts 50
- 5.7.6 Administration 50
- 5.7.8 Service 53
- 5.9.1 RS 232 56
- 5.9.2 RS 485 56
- 5.9.3 PROFIBUS DP 56
- 5.10.2 MAC address 58
- 5.10.3 IP address allocation 58
- 5.10.4 Subnet mask allocation 59
- 5.10.5 Gateway allocation 59
- 21 CFR 11 61
- 6.2.3 Administration 63
- 6.2.5 Analogue inputs 64
- 6.3.1 General 64
- Endress+Hauser 67 67
- 68 Endress+Hauser 68
- 7 Procedure in operation 69
- 7.2 The functions in detail 72
- 7.2.3 Enter comment / text 74
- 7.2.5 Extras 74
- 7.2.6 Set-up 77
- 8Accessories 78
- Software 79
- Operating language 79
- RSG12A1 79
- 80 Endress+Hauser 80
- 9.4 Spare parts 81
- 9.4.2 Spare parts list 82
- Endress+Hauser 83 83
- 9.5 Repairs/return 84
- 9.6 Disposal 84
- Measured variable / 85
- _ _ _ _ _ 86
- 10.3 Output values 87
- 10.4 Power supply 87
- 10.5 Accuracy 88
- 10.6 Operating conditions 88
- 10.7 Mechanical construction 89
- 320 mm (12.6“) 91
- 320 mm (12.6 “) 91
- 254 mm (10 “) 91
- 10.9 Data storage 92
- 10.11 Accessories 93
- 10.12 Further documentation 93
- BA 138R/09/en/08.04 98
- 51006049 98
- FM+SGML 6.0 98
Manuais e produtos relacionados com Ferramentas de medição e layout Promag CON-485 Series
(40 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais