Promag CON-485 Series Instruções de Operação Página 43
- Página / 98
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Memo-Graph S 5 Operation / adjusting device settings - Set-up to commissioning
Endress+Hauser 43
Set-up -> Signal settings -> Digital combinations -> Combination x
Function “Addition/Subtraction”: for impulse counter.
“Sum/average”: via impulse or operating time counter.
“Logical combination”: for control input, logging in/out, operating time and events + operating time
! Note!
Only those channels that it makes sense to combine can be selected. Combinations are processed like real signals, i.e.
they are updated every second, can be monitored for limit values and allocated to groups, etc.
Formula Description of the combination. Can not be changed (just for your information).
Sum of For “Sum/average” function:
Selection as to whether impulse or operating time counters are to be combined with each other in this combination. Can
only be selected when “Sum/average” is to be formed.
Channel identification Explanation (or designation of the combination carried out here).
Function “g” For “Sum/average” function:
Selection as to whether the average or the sum is to be calculated from channels “y1” to “y2”.
Input “y1” Input “y1”, which is to be combined with another.
! Note!
Other combinations can be used if their number is lower than the number of the current combination. In this way, for
example, combination 1 can be further processed in combination 2 (“Cascading”).
Logic condition y1 Only for “Logical combination” function:
Logic condition of input y1 at which the selected combination takes effect.
Selection: “High” or “Low”
Factor “a” For “Addition/Subtraction” function:
Factor “a”, by which the value from signal “y1” is multiplied.
Factory setting: 1.
Combination “?” For “Addition/Subtraction” function:
Addition/Subtraction: adds or subtracts both channels / formula parts.
“Not used”: switches part 2 of the formula (y2*b) off.
For “Logical combination” function:
“AND”: both inputs must accept the specified conditions in order to be recognised as logically true (“H”).
“OR”: it is sufficient if only one of both inputs accepts the specified condition.
Input “y2” Input “y2”, which is to be combined with another.
! Note!
Other combinations can be used if their number is lower than the number of the current combination. In this way, for
example, combination 1 can be further processed in combination 2 (“Cascading”).
Logic condition y2 Only for “Logical combination” function:
Logic condition of input y2 at which the selected combination takes effect.
Selection: “High” or “Low”
External switch Only for “Logical combination” function:
Switches the corresponding relay (or OC output) when the combination is logically true (“H”). The terminal numbers are
shown in brackets. Please refer to the connection instructions.
Factor “b” Addition/Subtraction: factor “b” by which the value of signal “y2” is multiplied.
Sum/average: factor by which the sum or the average of the channels “y1” to “y2” is multiplied.
Constant “c” Constant “c” is added to the result of the combination of both signals “y1” and “y2”.
Entry in this combination's (technical or physical) unit.
Factory setting: 0.
Engineering units Combination's technical (physical) unit, e.g. “piece” for summation of produced units.
Decimal point Number of places after the decimal point for the display and the limit value entry (counter limit value).
- Safety Data Manager (SDM) 1
- Memo-Graph S 1
- Overview 2
- Brief overview 2
- CHANGE PROTOCOL 3
- Table of contents 5
- 1 Safety instructions 7
- 1.4 Operational safety 8
- 1.5 Return 8
- 2 Identification 9
- 2.1.2 Product structure 10
- 3 Installation 11
- 3.3 Installation instructions 12
- 3.4 Post-installation check 12
- 4 Wiring 13
- 4 Wiring Memo-Graph S 14
- 14 Endress+Hauser 14
- 4.2 Terminal diagram 15
- 4.2.5 CPU board (slot 0) 19
- Ethernet connection 21
- 4.4 Ingress protection class 22
- 4.5 Post-connection check 22
- Set-up to commissioning 23
- 5.5 Set-up using PC 26
- 5.7.1 Basic settings 27
- 5.7.2 Signal settings 31
- Factory setting “0” 32
- 36 Endress+Hauser 36
- # Warning! 37
- " Caution! 38
- Endress+Hauser 43 43
- 44 Endress+Hauser 44
- 5.7.4 Products 48
- 5.7.5 Texts 50
- 5.7.6 Administration 50
- 5.7.8 Service 53
- 5.9.1 RS 232 56
- 5.9.2 RS 485 56
- 5.9.3 PROFIBUS DP 56
- 5.10.2 MAC address 58
- 5.10.3 IP address allocation 58
- 5.10.4 Subnet mask allocation 59
- 5.10.5 Gateway allocation 59
- 21 CFR 11 61
- 6.2.3 Administration 63
- 6.2.5 Analogue inputs 64
- 6.3.1 General 64
- Endress+Hauser 67 67
- 68 Endress+Hauser 68
- 7 Procedure in operation 69
- 7.2 The functions in detail 72
- 7.2.3 Enter comment / text 74
- 7.2.5 Extras 74
- 7.2.6 Set-up 77
- 8Accessories 78
- Software 79
- Operating language 79
- RSG12A1 79
- 80 Endress+Hauser 80
- 9.4 Spare parts 81
- 9.4.2 Spare parts list 82
- Endress+Hauser 83 83
- 9.5 Repairs/return 84
- 9.6 Disposal 84
- Measured variable / 85
- _ _ _ _ _ 86
- 10.3 Output values 87
- 10.4 Power supply 87
- 10.5 Accuracy 88
- 10.6 Operating conditions 88
- 10.7 Mechanical construction 89
- 320 mm (12.6“) 91
- 320 mm (12.6 “) 91
- 254 mm (10 “) 91
- 10.9 Data storage 92
- 10.11 Accessories 93
- 10.12 Further documentation 93
- BA 138R/09/en/08.04 98
- 51006049 98
- FM+SGML 6.0 98
Manuais e produtos relacionados com Ferramentas de medição e layout Promag CON-485 Series
(40 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais