Promag CON-485 Series Instruções de Operação Página 80
- Página / 98
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
9 Trouble-shooting Memo-Graph S
80 Endress+Hauser
9.3 Searching for and eliminating faults
Problem Cause Remedy
Analogue input shows “---” The signal lines are incorrectly connected or not connected. Please check the connections.
The input signal does not correspond to the configured sig-
nal.
Please check the input signal and the configuration.
The sensor is defective. Please check the input signal and replace the sensor.
Display does
not function
No LED lights
up
No power Please check the power supply and the mains supply.
Device fuse defective Please check the fuse on the power unit (1 A time-lag)
(see Chapter 9.4.1)
Power unit or CPU defective Please replace power unit or CPU (depending on
fault).
LED lights up Display defective Please replace the back lighting
CPU defective Please replace the CPU
ATA flash drive does not function ATA flash drive defective Please replace the ATA flash drive
CPU defective Please replace the CPU
Digital input does not function Incorrect connection Please check the connection and the digital input cir-
cuit.
Incorrect configuration Please check the digital input configuration.
Digital I/O board defective Replace digital I/O board.
Power unit defective Replace power supply board
Relays do not function Incorrect connection Please check the connection and the digital input cir-
cuit.
Incorrect configuration Please check the digital input configuration.
Digital I/O board defective Replace digital I/O board.
Multifunction output board defective Replace multifunction output board
Power unit defective Replace power supply board
Analogue outputs do not function Incorrect connection Please check the connection and the analogue output
circuit.
Incorrect configuration Please check the analogue output configuration.
Power unit defective Replace power supply board
Multifunction output board defective Replace multifunction output board
Configuration is locked Not logged in Please log in
Rear wall checking is active Only the administrator can log in.
Light barrier is defective Replace power supply board.
- Safety Data Manager (SDM) 1
- Memo-Graph S 1
- Overview 2
- Brief overview 2
- CHANGE PROTOCOL 3
- Table of contents 5
- 1 Safety instructions 7
- 1.4 Operational safety 8
- 1.5 Return 8
- 2 Identification 9
- 2.1.2 Product structure 10
- 3 Installation 11
- 3.3 Installation instructions 12
- 3.4 Post-installation check 12
- 4 Wiring 13
- 4 Wiring Memo-Graph S 14
- 14 Endress+Hauser 14
- 4.2 Terminal diagram 15
- 4.2.5 CPU board (slot 0) 19
- Ethernet connection 21
- 4.4 Ingress protection class 22
- 4.5 Post-connection check 22
- Set-up to commissioning 23
- 5.5 Set-up using PC 26
- 5.7.1 Basic settings 27
- 5.7.2 Signal settings 31
- Factory setting “0” 32
- 36 Endress+Hauser 36
- # Warning! 37
- " Caution! 38
- Endress+Hauser 43 43
- 44 Endress+Hauser 44
- 5.7.4 Products 48
- 5.7.5 Texts 50
- 5.7.6 Administration 50
- 5.7.8 Service 53
- 5.9.1 RS 232 56
- 5.9.2 RS 485 56
- 5.9.3 PROFIBUS DP 56
- 5.10.2 MAC address 58
- 5.10.3 IP address allocation 58
- 5.10.4 Subnet mask allocation 59
- 5.10.5 Gateway allocation 59
- 21 CFR 11 61
- 6.2.3 Administration 63
- 6.2.5 Analogue inputs 64
- 6.3.1 General 64
- Endress+Hauser 67 67
- 68 Endress+Hauser 68
- 7 Procedure in operation 69
- 7.2 The functions in detail 72
- 7.2.3 Enter comment / text 74
- 7.2.5 Extras 74
- 7.2.6 Set-up 77
- 8Accessories 78
- Software 79
- Operating language 79
- RSG12A1 79
- 80 Endress+Hauser 80
- 9.4 Spare parts 81
- 9.4.2 Spare parts list 82
- Endress+Hauser 83 83
- 9.5 Repairs/return 84
- 9.6 Disposal 84
- Measured variable / 85
- _ _ _ _ _ 86
- 10.3 Output values 87
- 10.4 Power supply 87
- 10.5 Accuracy 88
- 10.6 Operating conditions 88
- 10.7 Mechanical construction 89
- 320 mm (12.6“) 91
- 320 mm (12.6 “) 91
- 254 mm (10 “) 91
- 10.9 Data storage 92
- 10.11 Accessories 93
- 10.12 Further documentation 93
- BA 138R/09/en/08.04 98
- 51006049 98
- FM+SGML 6.0 98
Manuais e produtos relacionados com Ferramentas de medição e layout Promag CON-485 Series
(40 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais